- This topic is empty.
9th February 2006 at 20:16 #44145DMITRYGuest
Is anybody here who works on Nokia MSC?
Is there on line monitoring MML command in established call?
If yes, who is it?
I would like to know it.
And how is the procedure?
Waiting for your comments..
Pls help me !
dmtr10th February 2006 at 09:43 #44146MikGuest
ZMCJ:IMSI=10th February 2006 at 13:15 #44147DMITRYGuest
Thank you very much Mik !
Something else my friend, or, in any other friend.
Is ZMCJ command similar to MONTI command in AXE-10 Ericsson ?
In other words, can i have the content of the call with this command? (ZMCJ)
Thank you !11th February 2006 at 17:55 #44148MikGuest
Sorry, not familar with AXE. Try and compare 🙂 At least, you can see time-slots, A,B, C, romaing numbers, clear code, call setup phase.12th February 2006 at 12:12 #44149cybhertGuest
as far as I can remember.. they are pretty much similar… but on the side of nokia.. it is more detailed..ZMCJ:IMSI= , is a fairly powerfull command… this is what we basically used when we are troubleshooting.. clear codes can be also seen on the output print.16th February 2006 at 08:01 #44150techGuest
u cant hear the voice like in ericsson but u can get the details of the calls17th February 2006 at 23:55 #44151rahulGuest
what exactly is the diff b/w restarting a site by zefs and zefr ?18th February 2006 at 00:08 #44152EbrahimGuest
basically they are the same. But for reseting the site, you are allowed to reset only the OMU for Ultrasites (not applicable for metrosites).
With ZEFS, you do it for the whole thing.
Hope this clarifies.18th February 2006 at 10:01 #44153cybhertGuest
In Nokia.. you could also do the same..but the commands are hidden…and its strictly forbidden based on Laws…19th February 2006 at 09:08 #44154RahulGuest
i would also like to ask one more thing, in ZDDS; AFTER 00-MAN>
in extensions normally 1or 4 is for BCF PHASE MONITORING what info does the STAT coulmn give (the number)???20th February 2006 at 22:02 #44155EbrahimGuest
This is one of the good extensions to monitor the phases of BCF reset.
Basically, that column is used to indicate the result of each phase. If the number was zeros, then you are fine. if any problem happens (for example, BCF Configuration Failed), you will get a number. To know that that number is, use it with Mixed Cmnd Handling extension to figure out what was the reason so you can troubleshoot it easily.
Hope it is clear.
Regards3rd March 2006 at 01:21 #44156JoeGuest
If you use the ZMCJ command, you should first collect the IMSI with the ZMVO command.26th August 2010 at 07:24 #44157anand babuGuest
ZEFS; command is for site reset.
ZEFR; for omu reset- only 0&m link will alone get reset. This ZEFR will not affect the ongoing calls whereas ZEFS will make calls to terminate25th September 2015 at 18:16 #44158Shaikh MohsinGuest
I want to know MML Command for fetching below reports data from BSC I have MICRO forr all but i want MMl Command pls help me ASAP.
1. ND232 – DISTANCE RANGE DISTRIBUTION PER CELL
2. ND153 – ADJACENCIES HAVING HIGH HO FAILURE RATIO
3. ND138 – CELLS HAVING HIGH TCH RAW BLOCKING
4. ND166 – SDCCH DROP RATIO PER CELL
5. ND051 – BTS HAVING GPRS ENABLED TRXS
6. ND196 – UL AND DL QUALITY, UL INTERFERENCE PER TRX
7. ND061 – NON-SYMMETRICAL ADJACENCIES
8. ND154 – HO ATTEMPT CAUSE DISTRIBUTION BY CELLS
9. ND208 – LINK BALANCE PER TRX and many more.9th September 2019 at 07:58 #44159RameshGuest
Can any one help to convert nokia WBTS creation procedure by converting XML to MML commands (OR) MML commands to create WBTS in nokia.