- This topic has 39 replies, 1 voice, and was last updated 8 years, 9 months ago by Victor.
23rd May 2006 at 19:47 #43930pixGuest
yep, it’s the amount of trafic handled by the network at a certain time that matters (i.e. for dimensionning or for QoS monitoring reports, or whichever purpose).
Not a “virtual” max traffic that cannot happen…24th May 2006 at 11:24 #43931YvesGuest
The network have different BH than BTS, That is the fact. When dimensionning network elements, you have to considered individual BH for the BTS design, and BH given by MSC/BSC load for the rest of elements5th June 2006 at 22:09 #43932HSDEEPGuest
The BH at a BSC level is definitely not the sum of the BH of all cells. But it is usually possible to estimate it from the sum of the BH of all cells using a “Moderation Factor”. For instance with Alcatel, under classical call mix, you can get BH traffic by summing all BH at cell level and then by multiplying by 0.8 (moderation factor).4th September 2006 at 08:06 #43933hashemGuest
hi have a problem in data call
when i have a data call (GPRS)and recording any log with my tool(tems investigation) i have a expired time out (T3168 EXPIRED )and i have not any info about that ,can you help me about that ,what affect of this fault in my data network
HASHEM6th September 2006 at 09:56 #43934Tech ManGuest
Here’s the definition of T3168 timer:Wait for Packet Uplink Assignment message
The timer T3168 is used on the mobile station side to define when to stop waiting for a Packet Uplink Assignment message after sending of a Packet Resource request message.
The timer value is modifiable.The unit is 500ms (0=500ms, 1=1s, 2=1.5s, etc.)- Minimum value is 1 and Maximum value is 7. However, you’d need to wait for 5 minutes for the changes to take place. Also, you need to disable GPRS and Re-enable GPRS for those cells where GPRS is enabled for the changes to take effect.
Hope this helps.6th September 2006 at 16:57 #43935DJGuest
What are all the main KPIs we have to observe for CORE NW ?
Rgds6th November 2007 at 08:43 #43936asoGuest
may be you have congestion on PCH and check your CCCH configure.9th September 2008 at 20:09 #43937harsh kalraGuest
The T3168 timer is the timer which affects you TBF success ratio. Generally, the default value is 1000ms. when this timer expires, your TBF sucess ratio is affected if the TBF is not assigned in the stipulated timer expiry period. In short, it is like the RLT for TBF ass. sucesss22nd March 2011 at 06:26 #43938sdsGuest
Is the timer T3168 only for satellite sites or it also has effect on normal sites?1st April 2011 at 12:46 #43939billGuest
in our network tbf drop rate is almost 6%. i want to improve it to 2%. Any suggestions, the vendors are nokia and siemens….15th June 2011 at 05:34 #43940billGuest
any one please reply:
in our network tbf drop rate is almost 6%. i want to improve it to 2%. Any suggestions, the vendors are nokia and siemens….15th June 2011 at 09:18 #43941VickyGuest
what iare the values for N3101,N3103 & N31055th September 2011 at 14:13 #43942SandipGuest
TBF success rate can be improve by reducing the value of Inactive period UL TBF5th September 2011 at 18:34 #43943pixGuest
At the expense of degrading the network latency…
pix6th September 2011 at 23:06 #43944angyGuest
I have 2 questions =
1- there are call drops with the cause : suddenly loss, on the whole site. do you know it ?
2- how can I see interferences of a site, on the statistics (KPI) ?