Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

UL quality

Viewing 15 posts - 31 through 45 (of 68 total)
  • Author
    Posts
  • #43366
    Tech Man
    Guest

    Hi Tag,

    Since you have checked everything on the hardware part. There may be an external source of Interference like cordless phone users using the UL band. Why one of the operators here even found out the interference in G900 band was coming from odd sources like Marine radio from one of the merchant ships docked off the coast as well as a Church public address system 😉

    #43367
    Madhu
    Guest

    To Tag

    1)Tech Man is right even we have faced that problem

    2)Try to find out if some indoor boosters are installed in the near by area, the antenna of these boosters produce very high interference

    Regards
    Madhu

    #43368
    Boko
    Guest

    Hi,
    We are using repeaters for some indoor locations. We very often have the same problem when there is some problem with them. And when you change the frequency of course the interference still exists. It could even be installed by the competitor (not band selective as they are cheeper) several times it was some bad GSM gateways also. Also illegal boosters and cordless phones…
    Usually we go to the site with a yagi antenna and analyzer, and try to locate the interferer. the best way is to connect to analyzer to the GSM antenna to see the level of the interference.

    #43369
    Tag
    Guest

    Thanks Guys!!!!

    I think that is the only way i can do now.

    We have use a spectrum analyzer and found out that the interfence is in a large bandwidth.

    Any others to know who is transmitting?

    #43370
    Tech Man
    Guest

    Tag,

    Since as you said it is a wideband noise and no CDMA operators are present in your region.More likely than not, the external source of interference would be from an unknown source (eg. Illegal users etc) than a known source(Network operators), making it difficult to detect the source.

    Please check the following in the vicinity of your site in question:

    1) Any wideband repeater
    2) Bad mast head amplifiers (If Any)
    3) Earthing/ Sparking from any Electrical source.

    Contact you local Telecommunication Spectrum Administrator for support, as they have the requisite equipment and powers to detect and regulate such source,

    #43371
    Joe
    Guest

    it is occured often that uncompliant to EMC (electro magnatic compatability) in telecom equipment make alots supirous & interference to receiver.
    may such problem related with unefficent hardware immunity such as TRX damege or bad grounding, or probably Antenna defect(manufactury OR OLD antenna which may had metal part losses or radiators losses => intermodulation & degradation in Quality.
    B Regards.

    #43372
    Vijay
    Guest

    Tech Mann,

    According to my knw the fre. band of radio is limited to 30 to 300 MHz so it cant affected to 900 Mhz GSM band.

    according to u wht is the spectrum of Marine radio i heard first time this word.

    t28: can u plz conform how many users in this two sectors?

    #43373
    sachin bhushan
    Guest

    what is SDCCH drop at Abis.?
    what r the reasons ?

    #43374
    joe
    Guest

    In some countries coexist several radiocellular systems such as : TACS, AMPS, NMT900 with partly common frequency bands. It can be very difficult to detect if the interfered GSM frequency is not a BCCH.
    The effect is:
    • intermodulation with GSM BS/MS receiver,
    • spurious RACH for AMPS (AMPS Tx bands close to GSM uplink band),
    examination:
    • TACS : coverage hole with 600 m from TACS BTS
    • AMPS  50 % reduction of range if AMPS/GSM BTS collocated.
    Other RF Interferer (Radar, shop anti-theft mechanisms, medical device …) must be check case per case with a spectrum analyser, most of time on long period to detect sporadic or interference.

    #43375
    areeba
    Guest

    When interferer is a single frequency or with spectrum width limited, it can be sufficient to change frequencies on impacted sites.
    When disturbance is a spread over a large portion of spectrum, it could be necessary to add selective filters in BTS receiving section.
    In terms of parameters, it can be better to deactivated intracell handover flag(s), EN_INTRA_UL, EN_INTRA_DL, or even HO_Intracell_Allowed.

    #43376
    Rajiv Gujral
    Guest

    Is Uplink Qual goes worst only because of the other source of interference( that we can check in our daily report using avb_undec_RACH) or because of Hadware fault too..

    Regards

    #43377
    lodviche
    Guest

    Hi guys:
    Kindly i wonder about TRX hw problem, Cuz we encouter this in our network (alcatel) whereby we get LOW EFFICIENCY for TRXs daily, & just we replace it by other, so please what is the sensible reason beyond this problem, to avert this huge number of replacement which are (more than 4 low efficient TRXs per day)
    any Ad is highly appriciated.

    #43378
    Langer
    Guest

    Hi Lodviche,

    You may be facing a problem in the network because of improper installations. Better you check for VSWR. Also check the connectors connections properly.

    #43379
    John
    Guest

    Hi All,

    What is the prime reason for Intra-Cell Handover failures?

    Rgds,

    John

    #43380
    Pix
    Guest

    Hello John,

    The intracell HO can be caused by :
    – interference (UL or DL)
    – AMR

    As any handover, the process of this HO can be divided into two parts : the preparation phase and the execution phase (respectively, the request is validated as an attempt, and the attempt becomes a success).

    A preparation failure is due to congestion in the cell or a hardware failure (trx, combiner, sum, abis, bsc..).

    An execution failure is due to radio problems (interference to high in the target frequency, radio link is lost, …), or again, a hardware failure. Execution failure can be “saved” by a Reversion to the Old Channel (ROC).

    I hope it’ll help you…
    Good luck,
    Pix

Viewing 15 posts - 31 through 45 (of 68 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.