Generic selectors
Exact matches only
Search in title
Search in content

UL quality

  • This topic is empty.
Viewing 15 posts - 16 through 30 (of 68 total)
  • Author
    Posts
  • #43351 Reply
    t28
    Guest

    i think, firstly you shoud determine what type of drop call is it : system, radio, HO – check counters
    * maybe missing neighbour 🙂

    #43352 Reply
    Riz
    Guest

    Hi we can use. ZERO command to see if any interference on trx TSs.(e.g I.lev 4).
    Also we r using one report numbered 999. I don’t know whether it is custom made for us by the local Nokia vendor.
    It tells us bts wise what’s the reason for drop call. Wheather it is trx failures, transcoder fails, failures at A-bis, failures at A interface….

    Tk cr.

    #43353 Reply
    madhu
    Guest

    Hi Tag

    1)uplink quality are very weak if the combiner port is having problem, there are two combiner port pls check both the port for the output.

    2)Check the type of Antenna used

    Regards
    Madhu

    #43354 Reply
    Mandy
    Guest

    Thanks t28,

    What do u mean by the measurement from BTS?

    Can you tell more.
    Izzit the DL from the BTS you refering to?

    Tks,

    #43355 Reply
    Tag
    Guest

    Hi guys,

    Thanks again for the advice,

    Have run through the reports..
    H.O,pwr budget all seem ok.

    On for my UL quality which is very bad..

    My ops team have check all the equipment and all are tested ok.

    what we suspect now is external interference.

    Guys,

    Any ways to confirm the external interference gor G900?

    We have change a no of freqency however the problems is still there.

    Pls advice.

    Thanks

    #43356 Reply
    Tag
    Guest

    hi Riz…

    I have a similar report like urs however nothing much can be conclude from there.

    As what u have mention,

    failures at A-bis, failures at A interface,tch fail call,tch fail old,abis fail call,abis fail old,A if fail call,A if fail call.

    Can u kindly explained the reason for the above counters.
    cos in my report it does not really tell me much.

    Thanks alot!!

    #43357 Reply
    t28
    Guest

    to mandy…

    I mean, UL level which is measured by BTS and DL level, which is measured by MS and reported to BTS through measurement report…

    #43358 Reply
    Madhu
    Guest

    To Tag

    Pls check the CDMA interference.
    and check out ur combiner whether it is for GSM and or EGSM

    1)900 MHz band Uplink (MS transmitting and BS receiving) frequency range: 890 MHz ~ 915 MHz
    Downlink (BS transmitting and MS receiving) frequency range: 935 MHz ~ 960 MHz

    2)Extended 900 MHz band Uplink (MS transmitting and BS receiving) frequency range: 880 MHz ~ 915 MHz Downlink (BS transmitting and MS receiving) frequency range: 925 MHz ~ 960 MHz

    CDMA also operates in 820-888MHz so there is very high chance of Interference.

    CDMA downlink is were close to the uplink of the GSM frequecny so this can be one possible reason for the interference. In this case I suggest you to use BAND PASS FILTERS for the BTS and reduce the interference level.

    Regards
    Madhu

    #43359 Reply
    Nitin Kh
    Guest

    Well thanks for the info

    Its not the spectrum of CDMA which interferes sometimes ..Sometimes its the harmonics of the CDMA which may interfere..Although there always has to be a gaurd band between GSM & CDMA..But the harmonic(byproducts) have varying amplitude & frequency create the problem of interference. So, I personally think interference of CDMA on GSM uplink is irrespective of GSM/EGSM..

    Need more discussion on this…

    #43360 Reply
    Tag
    Guest

    thanks guys,

    For my network,

    We are only using only GSM900/1800.

    No CDMA/EGSM in our network.

    For now we suspect on it is a illegal transmission third party.

    Any advice on this.

    #43361 Reply
    Madhu
    Guest

    Ur right Nitin Kh Wht I meant for Mr.Tag is to check the same.

    To Tag
    it is always possible for the third party transmission, so better ask your RF Engineer for Drive test using both ur n/w SIM and the competitor n/w SIM

    Regards
    Madhu

    #43362 Reply
    Nitin Kh
    Guest

    Right Madhu, Illegal transmission is a probability..with the so much of frequency fuss

    #43363 Reply
    Nitin Kh
    Guest

    Mr. Tag ,

    Is it that you dont have any CDMA operator existing in the region you are working.??

    Regards,
    Nitin

    #43364 Reply
    t28
    Guest

    tag, why don’t you change all frequencies from problematic sector to another sector of this site vice versa ?
    it’s work for 10 minutes and you can confirm HW problem or not…
    how many TDMAs are in ‘bad’ sector, is there FH ?

    #43365 Reply
    Tag
    Guest

    Thanks guys,

    Yup there is no CDMA operator in my region.

    Ok for the hardware parts we ardy swar the freq and perform various test fron my ops team however there is no problems with the hardware portion.
    So far we have 3 sector in our site.

    Two of them are having drop call problems,whereas only one of the sector is normal.

    Any advice?
    Thanks

Viewing 15 posts - 16 through 30 (of 68 total)
Reply To: Reply #43351 in UL quality
Your information:




<a href="" title="" rel="" target=""> <blockquote cite=""> <code> <pre class=""> <em> <strong> <del datetime="" cite=""> <ins datetime="" cite=""> <ul> <ol start=""> <li> <img src="" border="" alt="" height="" width="">