Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

Faulty TS

Viewing 15 posts - 1 through 15 (of 15 total)
  • Author
    Posts
  • #43166
    About the Faulty Time Slot
    Guest

    Please tell me how a TS can be faulty as it is the logical channel (the bits) on the physical channel ( Frequency). So, a TS faulty should mean that a TRX is out of order but it is not said

    #43167
    John
    Guest

    Do you have enough resources in the cell to support the TS
    is the ABIS path available and correctly defined

    #43168
    Faulty TS @ John
    Guest

    John please elaborate your answer please as i can’t really understand…

    Thanks

    #43169
    TS
    Guest

    Are you talking about TDMA frames or the Physical TS ?
    If a TS is out of service there can be many reasons why

    Which equipment vendor is it

    #43170
    @TS by AG
    Guest

    I am talking about the Time Slot (AS I know that the Time slot is based on the TDMA principle) So i am asking about the time slot in the TRx of the BTS. As one TRx has one or in case of hopping (a list of frequencies). So TRx should be faulty if one TS is faulty, but it is not so. Wats the reason

    #43171
    RF Engr
    Guest

    Please any one tell the confusion of AG as I have the same issue

    #43172
    John
    Guest

    Which Vendor

    why do you think it is not possible to have just 1 TS Fail ?
    Example
    If there are not enough ABIS path available to the TRX then one TS could fail
    TS could fail loop test with TRC
    For example in older Ericsson RBS 200 there were 7 SPP cards in each TRX so 1 card could fail

    Again Which Vendor is it

    #43173
    RF Engr
    Guest

    Vendor is nortel so kindly tell me John about this

    #43174
    Boboo
    Guest

    Hi All,

    I’m aggre with John, I’ve ever seen this case : you locked the faulty TS and the KPI go back in their normal range. in nortel feature, you are abble to lock one TS in a TRX. Try to chek this

    Boboo

    #43175
    vijay
    Guest

    No it is not that when Trx faulty means hw problem and when TS faulty than it is issue of Multiframe in Radio propagation.

    #43176
    RF Engr
    Guest

    Thnaks for the comments but as I have said that TS faulty should have TRx faulty, i mean that TS is a logical channel as it is TDMA, so as far my knowledge is concerned, TS means the # of bits passing in a particular time (0.577 ms) in the same physical channel, so if one TS is faulty, so the Radio (Trx) should be. Thats was my logic. Also please tell me the exact refernce that how can i lock the TS

    #43177
    Boboo
    Guest

    HI

    to lock a TS (in Nortel), you had to access to the OMC.
    at the TDMA level,
    1st: right click on it with the mouse.
    2nd : selected the TS,
    3rd : click on the field “set channel state”
    4th : locked

    you have locked one TS slot of your TDMA.

    Regards

    Boboo.

    #43178
    RF Engr
    Guest

    Thanks Boboo but one of my question is unanswered yet. The question is ” TS means the # of bits passing in a particular time (0.577 ms) in the same physical channel, so if one TS is faulty, so the Radio (Trx) should be. Thats was my logic”

    #43179
    jood
    Guest

    1 ts faulty(hard ware) = all ts on trx fault.
    1 ts faulty(soft ware) = low efficiency of trx.
    1 ts drop = all other ts on trx may ok.
    1 ts block = trunkig gain of interface is bad.
    # ts failure might mean (HO, TRUNK, HW, SW,bad Qu,…. etc)

    #43180
    t28
    Guest

    usually, faulty TS is linked to wrong DCU4 board or TS is frozen. in case of frozen TS you should lock/unlock it…

Viewing 15 posts - 1 through 15 (of 15 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.