Erlang software tools...
Generic selectors
Exact matches only
Search in title
Search in content
Post Type Selectors

A-interface load in Nokia BSC

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • 28th October 2004 at 23:07 #40048
    Andy
    Guest

    Hi,

    I am new to Nokia BSC equipment, could anyone advise how to go about in using the mml command to output the traffic and BCSU load in NOKIA BSC?

    Thanks.

    29th October 2004 at 09:10 #40049
    alexander
    Guest

    to see processor load of BCSU use command: ZDOI:BCSU;
    to see how many LAPD channels on BCSU use command ZEEI::BCSU;
    to see how many channels on Aint use command ZCEL:CGR=1; , where 1 is a number of your Aint CGR.
    to see how many channels on Abis use command ZEEL:BL:

    alex
    http://www.dx200.biz

    29th October 2004 at 09:55 #40050
    Andy
    Guest

    Alex, thanks for your great advice and help. Am really appreciated it. By the way, is there any mml command to check whether downlink DTX is activated or not?

    Is downlink DTX recommended to be used? or any pre-caution need to be taken? any impact on a network using Half Rate feature? Your sharing on this matter is highly appreciated.

    Thanks.

    29th October 2004 at 14:00 #40051
    alexander
    Guest

    to see if DTX is used use command: ZEQO:BTS=1:MIS; where 1 is BTS number.
    DTX usage decrease interference so if frequecy re-use is at high level at your network then it is OK.
    Half Rate feature is a GREAT!!!!
    with half rate you can quickly increase amount of traffic channels 2 times !!! it’s great feature to fight with congestions on overloaded cells !!!

    alex
    http://www.dx200.biz

    30th October 2004 at 16:48 #40052
    Andy
    Guest

    Thank you Alex for you kind advice.

    Best regards,
    Andy

    1st December 2005 at 06:30 #40053
    Shakka
    Guest

    Dear all

    I need help about command Reference Manual for BSC Nokia DX-200 Platform.
    Please Sent to ibnu.shakka@plasa.com

    Many Thanks

    shakka

    1st December 2005 at 22:12 #40054
    alexander
    Guest

    shakka, the only source for Nokia DX200 commands is NED !!! You must have NED if your company use Nokia DX200 equipment. There is no other source of information for Nokia DX200.
    Alex
    http://www.dx200.biz

    14th July 2006 at 16:23 #40055
    Antonio
    Guest

    Hi all. Is there any MML command to set the coordinates in a new BCF or is this only possible by using the radio network manager?

    19th July 2006 at 03:41 #40056
    Rahul
    Guest

    hi all
    i m facing a problem of”bts with no transaction
    supp info 10″
    only thing i know is its related to gprs
    pls help

    20th April 2011 at 08:18 #40057
    raheel shahzad
    Guest

    how can we get transmission plane of bts from bsc

    20th October 2013 at 19:05 #40058
    ARUN KUMAR MISHRA
    Guest

    HI…EVERYONE AS WE KNOW BETWEEN TWO RNC IUR INTERFACE THEN WHAT WILL BE INTERFACE FOR TWO BSC IN 2G??

    21st November 2013 at 18:12 #40059
    jeff
    Guest

    what does DLCI stands for with association with the nokia bsc’s

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)
  • The forum ‘Telecom Design’ is closed to new topics and replies.