Diagnostics v1.04
Main Software Release: S1.2/Build 10
#
Power Supply Status:
DSP core . . . . . . . . : Ok
Ring/Feed . . . . . . . . : Ok
Testing DRAM @ 0x00000000..0x007fffff
Data lines (w1) . . . . . : Ok
Data lines (m1) . . . . . : Ok
Address lines . . . . . . : Ok
Bit integrity . . . . . . : Ok
PASSED
Ethernet Link Status . . . . : Link Ok
Parallel Ports Status
PA: 0 4 8 12
par —- ooii pp– iioi
dat 1000 00 0110
PB: 16 20 24 28
par iiio –oi oooo iooo
dat 1110 11 0001 0111
PC: 0 4 8 12
par —- ooii iiii oooi
dat 1100 0001 1100
PD: 0 4 8 12
par —o iiii oooo oooo
dat 1 0001 0011 1101
Testing DSP HPI @ 0x03000000
HPI data bus test . . . . : Ok
HPI DSP write test . . . : Ok
HPI DSP auto inc writes . : Ok
HPI DSP GG diagnostic . . : Ok
HPIC = 0x0000
Ethernet test . . . . . . . : Ok
QSLAC Test:
Initialise . . . . . . . : Ok
Read Config Reg . . . . . : Ok
Write Debnce Time Reg Cmd : Ok
Hardware Reset Cmd . . . : Ok
Revision Code = 0x13
Main Board Revision . . . . : 1
Option Board Id . . . . . . : 7
Board Configuration Information
===============================
Boot Line: . . . . . . . . . : “cpm(0,0)dfi-815:updater.ftp e=192.168.1.4”
MAC Address . . . . . . . . : 00-60-c4-f0-04-0b
Auto Boot Flag . . . . . . . : 2 -> start everything
IP Address . . . . . . . . . : 192.168.1.4
Default Gateway IP Address . : 0.0.0.0
Default Netmask . . . . . . : 255.255.255.0
Debug Monitor
(type “?” for help)
>
> ?
Available commands:
1. dsp DSP HPI test
2. eet Eerom test
3. eer Eerom read
4. eew Eerom write
eg.
eew 1a=124f Write 0x124f to EE addr 0x1a
5. erase Eerom erase
6. eth Ethernet test
7. hpi Diagnose DSP HPI
8. info Show configuration info
9. m[b,w,l]
m[b,w,l] =
Memory dump diagnostic.
Where addr, length & data are in hex.
eg.
m 200 10 Read 0x10 bytes at address 0x200
mw 200 10 Read 0x10 words at address 0x200
ml 200 10 Read 0x10 longs at address 0x200
ml 200=10 Set 0x200 to 0x00000010
10. p[a,b,c,d]
p[a,b,c,d]=
Parallel i/o port diagnostic.
eg.
pa Display Port A data latch
pa=0b00 Write 0x0b00 to Port A data latch
11. qi Initialise QSLAC
qs Read QSLAC status word
qw XX XX XX …, y Write hex bytes 0xXX to the QSLAC
and then receive decimal y bytes
12. rf on Enable the ring/feed power supply
rf off Disable the ring/feed power supply
rf x Enable the ring/feed supply for x * 100ms
Where x = 1..99
13. ring 15[20,25,50] Set the ringer frequency (Hz).
14. . Repeat last command.
15. , Recall last command.