Free Erlang traffic calculators

The world's first online Erlang traffic calculators

Telecom Traffic Online
  Home | Free calculators | Products | Tech. papers | Forum | About us
A-Z termination - click here
A-Z termination - CLICK HERE
VoIP bandwidth calculator
  • VoIP softswitch

    DUAL Softswitch is a complete Voice over IP switching and billing solution.  Flat monthly rate.

    Web control panels; Least Cost Routing; Excel tariff uploads; SIP and H323 support.

    H323 SIP softswitch >>

  • VoIP calling

    Premium quality termination for wholesale carriers with their own VoIP switch.

    44Direct >>

    Our lowest rates for wholesale carriers with their own VoIP switch.

    44Mobile >>

    Our unique online callshop billing system.

    Bill My Calls >>

Bandwidth calculation

Mahmoud - 6th December 2017  (06:02 GMT)

i have a daily transaction of 4GB from 200 concurrent users, so what is the leased line bandwidth i will required ?

Ajit - 14th July 2016  (07:17 GMT)

How much bandwidth is sufficient to cater to normal internet surfing by 150 users plus uploading video data 12 cameras?

samir p vyas - 28th October 2015  (13:42 GMT)

how to calculate 10 MBPS leased line , If i download one file and so me as a 1280 KBPS. Then it is Correct or Not ?

dmck - 11th September 2003  (00:42 GMT)

Marlon, your calculation assumes that all computers are using 32Kb continuously whilst connected to the internet. IN fact they are using the 32Kb or more for only relatively short durations (sometimes only seconds)usually during upload/download. Down loads are usually bigger files. To calculate the maximum number you need to know the average time they are downloading data and divide this into 1 hour or find the average download file size (in bits) and divide into 2M x 3600 (bits per hour).

These calcs wil more closely approximate the max number of PC's to connect.

Marlon - 10th September 2003  (08:53 GMT)

Would appreciate for an answer about a calculation that I am not sure of.

I have 2Mbps leased line to access the internet.

I have a network that allows many computers to access the internet via my leased line using dial-up networking.

What is the maximum number of dial-up computers that can connect with a minimum speed of 32Kbps?

Should I just divide the 2MB to the number of dial up computers and come up with 32Kbps?

Thank you.

Need Help - 25th July 2003  (04:54 GMT)

Appreciate it you could help me to calculate the time needed to transfer the amount of data 24KB across a 16Kbps analog line with 16Bytes CIR. Please show the geneine formula on the calculation.

Thanks in advance.

Zahid - 1st May 2003  (20:42 GMT)

One more thing I mean question in the same context, how MRTG shows the bandwidth utilization??

Don McK - 6th February 2003  (02:39 GMT)

The 64kb is the speed of the data on the line and it should be a true 64kb, after all, that is what you are paying for.

You are probably using a networking protocol which places some overheads on the data, for exaple both IP and Frame relay add additional data packets (for addressing, error detection etc). You may also be using a file transfer application which does its own error detection and asks for some data to be re-sent.

This additional data is an overhead on your file, but it must be included in the total data transmitted. For instance a 20% overhead adds 40Mb or approximately an additional 84 minutes.

The transfer speed will also depend upon the efficiency of the network at either end, (getting from PC to router and router to PC) and the efficiency of the router (It may be operating at near capacity and queuing data)

There are lots of areas where delays can be introduced, it can be a very specialised task to actually find the cause and a very expensive exercise to 'fix' it.

Good Luck.

Don McK

Manoj Kumar C. - 5th February 2003  (13:00 GMT)


Many Thanks for the information.
Note that in an actual scenario it took around 12.5 hours to complete this transfer. Do you think the margin should be that big?

Thanks & Cheers,

Manoj Kumar

Anwer Jalil - 5th February 2003  (07:35 GMT)

A leased line of 64 kilobit per second can carry 64/8 kilobytes per second for bytes consisting of 8 bits. Therefore, a file of 200MB data will take 200,000/8/60/60 hours i.e. about 7 hours. However, please keep in mind that a leased line of 64kb/s never delivers true 64k, so you should put some margin for that


Anwer Jalil

Other messages

Other messages: [Next 10 >>]

Post a reply to this article

Name Enter your name.
Message Enter your message.
Email Optional -  If you enter your email address in this box, then you will automatically be notified if anyone replies to your message.  Your email address will only be published if you pay to post this message.
Please confirm you are human.
Press the button to post your message.
Home | Free online calculators | Products | Technical papers | Forum | Contact us | About us

Last modified: 17 May 2017

Copyright 2017. All rights reserved.