Free Erlang traffic calculators

The world's first online Erlang traffic calculators

Telecom Traffic Online
  Home | Free calculators | Products | Tech. papers | Forum | About us
A-Z termination - click here
A-Z termination - CLICK HERE
VoIP bandwidth calculator
  • VoIP softswitch

    DUAL Softswitch is a complete Voice over IP switching and billing solution.  Flat monthly rate.

    Web control panels; Least Cost Routing; Excel tariff uploads; SIP and H323 support.

    H323 SIP softswitch >>

  • VoIP calling

    Premium quality termination for wholesale carriers with their own VoIP switch.

    44Direct >>


    Our lowest rates for wholesale carriers with their own VoIP switch.

    44Mobile >>


    Our unique online callshop billing system.

    Bill My Calls >>

NOKIA MML COMMAND

Ramesh - 9th September 2019  (07:58 GMT)

Can any one help to convert nokia WBTS creation procedure by converting XML to MML commands (OR) MML commands to create WBTS in nokia.

Shaikh Mohsin - 25th September 2015  (18:16 GMT)

Dear All,

I want to know MML Command for fetching below reports data from BSC I have MICRO forr all but i want MMl Command pls help me ASAP.

Thanks.

1. ND232 - DISTANCE RANGE DISTRIBUTION PER CELL
2. ND153 - ADJACENCIES HAVING HIGH HO FAILURE RATIO
3. ND138 - CELLS HAVING HIGH TCH RAW BLOCKING
4. ND166 - SDCCH DROP RATIO PER CELL
5. ND051 - BTS HAVING GPRS ENABLED TRXS
6. ND196 - UL AND DL QUALITY, UL INTERFERENCE PER TRX
7. ND061 - NON-SYMMETRICAL ADJACENCIES
8. ND154 - HO ATTEMPT CAUSE DISTRIBUTION BY CELLS
9. ND208 - LINK BALANCE PER TRX and many more.

anand babu - 26th August 2010  (07:24 GMT)

ZEFS; command is for site reset.
ZEFR; for omu reset- only 0&m link will alone get reset. This ZEFR will not affect the ongoing calls whereas ZEFS will make calls to terminate

Joe - 3rd March 2006  (01:21 GMT)

If you use the ZMCJ command, you should first collect the IMSI with the ZMVO command.

Ebrahim - 20th February 2006  (22:02 GMT)

Hi Rahul,

This is one of the good extensions to monitor the phases of BCF reset.

Basically, that column is used to indicate the result of each phase. If the number was zeros, then you are fine. if any problem happens (for example, BCF Configuration Failed), you will get a number. To know that that number is, use it with Mixed Cmnd Handling extension to figure out what was the reason so you can troubleshoot it easily.

Hope it is clear.

Regards

Rahul - 19th February 2006  (09:08 GMT)

thanx Ebrahim
i would also like to ask one more thing, in ZDDS; AFTER 00-MAN>
in extensions normally 1or 4 is for BCF PHASE MONITORING what info does the STAT coulmn give (the number)???

cybhert - 18th February 2006  (10:01 GMT)

Hello Tech...

In Nokia.. you could also do the same..but the commands are hidden...and its strictly forbidden based on Laws...

Ebrahim - 18th February 2006  (00:08 GMT)

Hi Rahul,

basically they are the same. But for reseting the site, you are allowed to reset only the OMU for Ultrasites (not applicable for metrosites).
With ZEFS, you do it for the whole thing.

Hope this clarifies.

rahul - 17th February 2006  (23:55 GMT)

hi
what exactly is the diff b/w restarting a site by zefs and zefr ?

tech - 16th February 2006  (08:01 GMT)

Hi,

u cant hear the voice like in ericsson but u can get the details of the calls

Other messages

Other messages: [Next 10 >>]

Post a reply to this article

Name Enter your name.
Message Enter your message.
Email Optional -  If you enter your email address in this box, then you will automatically be notified if anyone replies to your message.  Your email address will only be published if you pay to post this message.
Verification
Please confirm you are human.
Press the button to post your message.
Home | Free online calculators | Products | Technical papers | Forum | Contact us | About us

Last modified: 17 May 2017

Copyright 2017. All rights reserved.